Vol. 15 No. 02 (2025): Journal of Materials & Construction
##common.pageHeaderLogo.altText##
JOURNAL OF MATERIALS & CONSTRUCTION

ISSN: 2734-9438

Website: www.jomc.vn

An assessment of terrazzo tile properties: effect of waste incineration bottom ash content

Huynh Trong Phuoc , Bui Quoc Trung , Van Pham Dan Thuy

Keywords:

Terrazzo tiles
Waste incineration bottom ash
Flexural strength
Water absorption
Surface abrasion

Abstract

The increasing scarcity of natural aggregates and the rising cost of raw materials in the construction industry are driving the demand for sustainable alternatives. At the same time, municipal solid waste incineration generates significant volumes of bottom ash, which is typically landfilled, posing environmental and economic challenges. This study explores the technical and economic feasibility of using waste incineration bottom ash (WIBA), blended with coal thermal fly ash (FA), as a partial or full substitute for crushed sand in the production of terrazzo tiles—a high-value, architectural cementitious product requiring strong mechanical performance and a polished surface finish. Five mix designs were developed, with WIBA-FA blends at a fixed WIBA:FA ratio of 75:25 by mass were used to replace 0% (control), 70%, 80%, 90%, and 100% crushed sand in the mixtures. The tiles were fabricated using a semi-dry pressing method and cured for 28 days before testing. Experimental evaluation included flexural and compressive strengths, full and surface water absorption, surface abrasion resistance, and material cost analysis. Results showed that the mix (X5) with 70% WIBA inclusion achieved a 30.1% reduction in cost while meeting all technical requirements, with compressive and flexural strengths of 28.6 MPa and 3.8 MPa, respectively. Moreover, a multivariate overall performance score was developed to identify the optimal formulation by integrating normalized strength, durability, and cost metrics. The experimental outcomes demonstrate the viability of using WIBA–FA blends in high-finish terrazzo tiles and contribute a quantitative framework for material optimization under sustainability and performance constraints.

User Navigation

PDF

How to Cite

Huynh Trong Phuoc, Bui Quoc Trung, & Van Pham Dan Thuy. (2025). An assessment of terrazzo tile properties: effect of waste incineration bottom ash content. JOURNAL OF MATERIALS & CONSTRUCTION, 15(02), Page 4 – Page 12. https://doi.org/10.54772/jomc.v15i02.1084

References

  1. J. Eun Kim, J. Seo, K.-H. Yang, and H.-K. Kim, “Cost and CO2 emission of concrete incorporating pretreated coal bottom ash as fine aggregate: A case study,” Construction and Building Materials, vol. 408, p. 133706, Dec. 2023, doi: 10.1016/j.conbuildmat.2023.133706.
  2. H. Chu, Q. Wang, and W. Zhang, “Optimizing ecological ultra-high performance concrete prepared with incineration bottom ash: Utilization of Al2O3 micro powder for improved mechanical properties and durability,” Construction and Building Materials, vol. 426, p. 136152, May 2024, doi: 10.1016/j.conbuildmat.2024.136152.
  3. H. P. Nguyen, A. Mueller, V. T. Nguyen, and C. T. Nguyen, “Development and characterization of lightweight aggregate recycled from construction and demolition waste mixed with other industrial by-products,” Construction and Building Materials, vol. 313, p. 125472, Dec. 2021, doi: 10.1016/j.conbuildmat.2021.125472.
  4. J. Lu et al., “Utilization of municipal solid waste incinerator bottom ash (MSWIBA) in concrete as partial replacement of fine aggregate,” Construction and Building Materials, vol. 414, p. 134918, Feb. 2024, doi: 10.1016/j.conbuildmat.2024.134918.
  5. A. Adediran, S. M. Kikky, S. K. Adhikary, V. Ducman, and P. Perumal, “Upcycling municipal solid waste incineration bottom ash in clay-bonded bricks,” Ceramics International, vol. 51, no. 7, pp. 8941–8954, Mar. 2025, doi: 10.1016/j.ceramint.2024.12.324.
  6. H. Zou, P. He, F. Lü, and H. Zhang, “Practice and challenges for beneficial use of municipal solid waste incineration bottom ash in China,” Journal of Environmental Chemical Engineering, vol. 13, no. 5, p. 117923, Oct. 2025, doi: 10.1016/j.jece.2025.117923.
  7. K. Godyń, B. Dutka, C. Rosik-Dulewska, T. Ciesielczuk, and M. Głowacki, “Assessment of the possibility of heavy metals elution from municipal solid waste incineration bottom ash into the soil and water,” Desalination and Water Treatment, vol. 323, p. 101282, Jul. 2025, doi: 10.1016/j.dwt.2025.101282.
  8. M. H. Sliem, M. Irshidat, M. K. Hassan, Y. Manawi, and M. Al-Ejji, “Mechanochemical treatment of incinerated municipal bottom ash in CO2-rich environment for sustainable waste management practices,” Journal of Environmental Management, vol. 389, p. 126171, Aug. 2025, doi: 10.1016/j.jenvman.2025.126171.
  9. Y. Yuan et al., “Advancing the applicability of recycled municipal solid waste incineration bottom ash as a cement substitute in printable concrete: Emphasis on rheological and microstructural properties,” Journal of Building Engineering, vol. 103, p. 112133, Jun. 2025, doi: 10.1016/j.jobe.2025.112133.
  10. J. Liu et al., “Study on the mechanical properties and durability of epoxy mortar for municipal solid waste incineration bottom ash,” Construction and Building Materials, vol. 493, p. 143154, Sep. 2025, doi: 10.1016/j.conbuildmat.2025.143154.
  11. J. Yan, Z. Li, and J. Wang, “Municipal solid waste incineration bottom ash-based ultra-high performance cement mortar: Multi-scale performance evolution and synergistic mechanism of life cycle environmental benefits,” Construction and Building Materials, vol. 493, p. 143228, Sep. 2025, doi: 10.1016/j.conbuildmat.2025.143228.
  12. Y. Li et al., “Optimization of municipal solid waste incineration bottom ash geopolymer with granulated blast furnace slag (GGBFS): Microstructural development and heavy metal solidification mechanism,” Case Studies in Construction Materials, vol. 22, p. e04423, Jul. 2025, doi: 10.1016/j.cscm.2025.e04423.
  13. Z. Zhang et al., “Preparation and performance improvement of municipal solid waste incineration bottom ash based geopolymer modified by self-extracted CaO,” Construction and Building Materials, vol. 468, p. 140447, Mar. 2025, doi: 10.1016/j.conbuildmat.2025.140447.
  14. Q. Yuan, D. Robert, A. Mohajerani, P. Tran, and B. K. Pramanik, “Utilisation of waste-to-energy fly ash in ceramic tiles,” Construction and Building Materials, vol. 347, p. 128475, Sep. 2022, doi: 10.1016/j.conbuildmat.2022.128475.
  15. L. Du et al., “Study on the preparation and formation of municipal solid waste incineration bottom ash-coal fly ash-based shaped phase change paraffin,” Construction and Building Materials, vol. 490, p. 142575, Sep. 2025, doi: 10.1016/j.conbuildmat.2025.142575.
  16. T.-P. Huynh, D.-T. Van-Pham, T.-K. Lam, V.-L. Tran, and Q.-T. Bui, “Properties evaluation of terrazzo tiles produced for external use using a fine aggregate from a domestic waste incineration plant,” Journal of Science and Technology in Civil Engineering, vol. 18, no. 4, pp. 1–11, Dec. 2024, doi: 10.31814/stce.huce2024-18(4)-01.
  17. L. Kherraf, H. Hebhoub, A. Abdelouahed, and W. Boughamssa, “Comparative study on the performance of sand-based mortars from marble, floor tile and cinder block waste,” Journal of Building Engineering, vol. 45, p. 103433, Jan. 2022, doi: 10.1016/j.jobe.2021.103433.
  18. G. Deng et al., “Pozzolanic reactivity of carbonated high-calcium fly ash: A mechanism study,” Construction and Building Materials, vol. 446, p. 138015, Oct. 2024, doi: 10.1016/j.conbuildmat.2024.138015.
  19. T. Tang, L. Cai, K. You, M. Liu, and W. Han, “Effect of microwave pre-curing technology on carbide slag-fly ash autoclaved aerated concrete (CS-FA AAC): Porosity rough body formation, pore characteristics and hydration products,” Construction and Building Materials, vol. 263, p. 120112, Dec. 2020, doi: 10.1016/j.conbuildmat.2020.120112.
  20. S. Y. N. Chan and X. Ji, “Comparative study of the initial surface absorption and chloride diffusion of high performance zeolite, silica fume and PFA concretes,” Cement and Concrete Composites, vol. 21, no. 4, pp. 293–300, Aug. 1999, doi: 10.1016/s0958-9465(99)00010-4.